KWM Gutterman PANTHER Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 37

background image

Moving the guides to acquire 1 3/8" of metal as illustrated on pg.13 (EXAMPLE
PROBLEM TO MUCH LIP. (1) REMOVE CENTER COVER AND FRONT LID. (2) WITH
GUTTER RUN THROUGH GUILLOTINE 12" BACK GUTTER UP 6" CHECK FOR
DOUBLE TRACK AT ENTRANCE OF BOX WHERE 1 3/8" BENT MEETS WITH
BOTTOM OF INSIDE BOX ROLLERS. (3) MEASURE AMOUNT OF COIL IN BOX 1 5/
8" INCORRECT AMOUNT OF METAL. (4) MEASURE RIGHT GUIDE SHOE NOTE
MEASUREMENT, MOVE RIGHT GUIDE SHOE FROM WALL TO THE LEFT 1/8" KEEP
GUIDE PARALLEL TO WALL. (5) MOVE LEFT GUIDE TO THE LEFT ALLOWING
ENOUGH ROOM FOR COIL. (6) INSERT A 2' LONG PIECE OF COIL STOCK INTO
THE GUIDE SYSTEM UP TO THE RIGHT GUIDE.
(7) MOVE THE LEFT GUIDE TO RIGHT UNTIL IT LIGHTLY TOUCHES THE LEFT
EDGE OF THE COIL. (8) TIGHTEN ALL BOLTS. (9) FEED THE MACHINE AND
CHECK FOR 1 3/8" OF METAL.

– 33 –

«
...
33
34
35
36
37
»

Содержание PANTHER






































Отзывы:

Нет отзывов

Похожие инструкции для PANTHER

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGER WERKEN Страницы: 2

Бренд: JB-Lighting Страницы: 32

Бренд: W&H Страницы: 72

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды