SECTION II
Operation
P 2.3
D. ADJUSTING THE PRINT FORCE:
Figure 2.2 & 2.3
DO NOT USE EXCESSIVE PRINT FORCE TO
COMPENSATE FOR PRINTING IMPERFECTIONS.
The operator can adjust the print force.
Always operate the printer with the minimum print
force that will produce acceptable printing. A quarter
turn of the knob is a large adjustment. If a
significant change in print quality is not noticed,
return to the previous setting and refer to Section III,
Adjustments and Section IV, Trouble Shooting to
correct any problems.
When the ink roll will no longer adequately ink the
type, replace it. Do not attempt to extend the life of
the ink roll by increasing the printing force.
To increase the print force, turn the knob counter-
clockwise. If the effort to turn the knob suddenly de-
creases, the maximum print force has been reached.
To decrease the print force, turn the knob clock-
wise.
E. CLOSING BAGS:
Figure 2.4
1. Grasp the bag as shown. Spin the bag to twist
the bag neck. Twisting the bag helps the
material to enter the closure smoothly.
2. The lower hand should form a “V” to trap all of
the bag material. This helps to completely
insert the bag material into the closure opening.
3. Do not jam the bag material straight into the
closure opening. The top hand should lead the
bottom hand. Follow up with the lower hand
until all of the bag neck is in the closure. A tight
package is accomplished by holding the
contents of the bag snugly up against the
underside of the closure track.
4. Remove the closed bag with a horizontal
motion.
086B 02 18
Figure 2.2
View window
Rotate printhead
Knob
(print force)
Selector
knob
Spacer
Typeholder block
Knurled knob
Figure 2.3
Knob
(Ink roll)
Содержание 086B-100
