SECTION III
Adjustments
P 3.3
D. CHECK POSITION:
Figure 3.3
The check stops the closure strip from moving
backward while the pick retracts.
Refer to Figure 3.3 to further understand the check
mounting position. For this adjustment the closure
track must be removed from the closer.
For models 200, 600, and 700 the check is mounted
in the back mounting holes (farthest from the front of
the closure track). For Model 100, the check is
mounted in the front mounting holes.
1. With the check mounted in the correct holes,
and the mounting screws loose, slide the check
forward toward the front of the closure track to
the end of the mounting slots and tighten the
mounting screws.
E. CLOSURE STOP POSITION:
Figure 3.3 and 3.4
The end closure is separated from the closure strip
while the closure stop limits the travel of the second
closure in the strip as the pick continues to advance
the first closure. As with the position of the check,
the stop mount is located in a specific way
depending on the closer model being adjusted.
1. The stop mount is mounted as shown.
2. Be sure the beveled edges of the mount are
facing the closure stop.
The closure stop tip must be centered in the slot
located in the bottom track for it.
3. Slightly loosen the stop mount mounting screws.
4. Move the closure stop tip side to side until it is
centered in the slot.
5. Tighten the mounting screws.
6. Turn the closure track assembly over so it is
right side up. Again check the position of the
closure stop tip as this is the way the track as-
sembly is oriented during operation. Readjust if
needed.
086B 02 18
Closure stop
setscrew
Beveled edges of
the stop mount
Closure stop
Figure 3.4
(Stop mount is positioned for Models 200, 600, 700)
Figure 3.5
Содержание 086B-100
