SECTION III
Adjustments
P 3.13
S. PRINT FORCE- SIDE TO SIDE:
Figure 3.18
The print head must be aligned so the typeface
contacts the closure uniformly from side to side.
Verify that the type is properly inked. (Refer to Part
Q, and Part R this section).
1. Adjust the print force to a very light setting to
accentuate the variation in the print quality. This
indicates how flat the typeface is to the print sur-
face. Verify that the type is being properly inked.
If the line of printing is not uniform, the bearing
mount can be moved vertically to raise or lower
that end of the printer shaft as shown in Figure
3.18.
2. Slightly loosen the two socket head screws that
hold the bearing mount.
3. Move the bearing mount only about 1/32" (1mm)
and then reevaluate the print force.
4. Verify that the side-to-side location of the
printhead has not changed and that the inking
force is still uniform across the typeface.
086B 02 18
Figure 3.21
Figure 3.22
Figure 3.23
Printer cam arm
adjustment screw
Printer cam
Printer cam
bearing
Band
printhead
Printer cam arm
Printer link
Print adjust
arm
Print adjust
knob
Band printer
lever
Printer arm pivot
mounting screw
Printer cam bearing
Power switch
Ready light
Run switch
Содержание 086B-100
