SECTION III
Adjustments
P 3.10
M. CAM ASSEMBLY LATERAL ALIGNMENT:
Figure 3.14 and 3.15
1. Set the lateral (side to side) position of the cam
assembly so the outside edge of the stop cam
measures 15/16” (24mm) from the outside edge
of the motor plate.
2. Rotate the cam assembly to position the set
screw over the flat on the motor shaft and
tighten the set screw. The angular position of
the cam assembly is not important because the
motor will stop with the cam in the correct
position when the switch cam contacts the limit
switch. Threadlocking compound should be
used to lock the set screw in place.
3. Tighten the set screw.
N. CAM SWITCH MOUNTING:
Figure 3.15
The cam switch allows the cam assembly to rotate
and only stop when a closure reaches the bag
closing position. The switch cam actuates the
switch. If the toggle switch is in the “RUN” position,
the “READY” light will be on while the cam switch is
actuated. The cam switch should not need adjust-
ment.
CAUTION MOTOR ROTATION.
Inadvertently rotating the motor shaft manually can
damage the cam switch (Figure 3.25). If the motor is
to be manually rotated
ONLY ROTATE THE MOTOR
CLOCKWISE FROM THE FAN END OF THE
MOTOR
(Figure 3.25). If the motor shaft is turned in
the opposite direction (counterclockwise from the fan
end of the motor) the cam switch will likely be dam-
aged.
THE REMAINING ADJUSTMENTS IN THIS SECTION
ARE FOR THE 086B PRINTER OPTION.
O. PRINTHEAD LOCATION - SIDE TO SIDE:
Figure 3.16
The printhead should be centered between the
sides of the closure strip. If it is not, it will not align
properly with the ink roll. The printhead can be
manually pressed against the closure to determine
where the image will be on the closure. The band
printhead must be rotated back against the spacer
at all times. To center the printhead, loosen the
set screw in the printer block lever and slide the
printhead assembly along the printer shaft. When
the set screw is tightened, it should bear against a
flat on the printer shaft. The two set screws in the
set collars and the set screw in the printer lever
should be in line.
086B 02 18
Figure 3.16
Printer block lever
setscrew. Loosen to adjust
the print head side to side.
Bearing bracket mounting
screws (2). Loosen to adjust
print head front to back.
Print head side to
side adjustment
Содержание 086B-100
