KVH Industries TracVision HD11 Скачать руководство пользователя страница 9

Страница: 9 / 39

Plan the installation of the belowdecks

equipment by using the Installation Worksheet

and following the requirements in this section:

• Multiswitch Requirements

• Installation Location Requirements

• Mounting Options

• SmartSwitch Requirements (if equipped)

• Cable Requirements

• AC Power Requirements

• Grounding Requirements

Multiswitch Requirements

Using the Installation Worksheet, plan and

record multiswitch requirements based on the

number of tuners needed. Refer to the

Installation Worksheet for details.

Installation Location Requirements

• Choose belowdecks installation locations that

are dry, well-ventilated, and away from any

heat sources or salt spray.

• Ensure the ACU mounting location(s)

provide adequate Wi-Fi reception. Do not

install in an area surrounded by metal or near

any electrical devices that emit RF noise.

• In order to use the supplied power/data

cable, the antenna must be mounted within

100 ft (30 m) of its ACU. However, you can

order a longer cable if needed – contact KVH

for details.

• If you are installing a SmartSwitch and you

wish to use the supplied PC data cable,

ACU A must be installed within 3 feet (1 m)

of the SmartSwitch. However, longer cabling

may be used – contact KVH for details.

Plan the Belowdecks Installation

Figure 7 ACU Dimensions

CONTROL UNIT

ANTENNA

POWER

MENUS

CHANGE

EXIT

Side View

Front View

19.00"

(48.26 cm)

16.75"

(42.55 cm)

2.63"

(6.68 cm)

18.31"

(46.51 cm)

1.75"
(4.45 cm)

0.44"

(1.12 cm)

4 x

11.18"
(28.40 cm)

16.31"

(41.43 cm)

Strain Relief Bracket

1.02"

(2.60 cm)

4.81"
(12.22 cm)

ø.

25"

(0.64 cm)

Top View

Содержание TracVision HD11








































Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды

KVH Industries TracVision HD11, Руководство по установке

Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды