KVH Industries TracVision HD11 Скачать руководство пользователя страница 30

Страница: 30 / 39

The wiring diagrams in this section support a

variety of configurations and hardware. Refer to

the applicable wiring diagrams for your

installation.

Wiring SWM and Non-SWM Hardware

Only DIRECTV programming in North America

supports SWM-compatible receivers and DVRs

(see Figure 46). All linear receivers/DVRs and

other circular receivers/DVRs are not SWM-

compatible.

NOTE:

Additional SWM-compatible receivers/DVRs

might become available at any time. If your receiver or
DVR model is not listed here, check its manual to see
if it is SWM-compatible.

Basic Diagram

Wiring One Antenna/ACU with up to 32 Tuners

(see page 30)

SmartSwitch Input Wiring Diagrams

• One Antenna/ACU (see page 31)

• Two Antennas/ACUs (see page 32)

SmartSwitch Output Wiring Diagrams

• Overview (see page 33)

• 32 Non-SWM-compatible Tuners (see

page 34)

• 16 SWM-compatible Tuners and 32 Non-

SWM-compatible Tuners (see page 35)

• 32 SWM-compatible Tuners and 32 Non-

SWM-compatible Tuners (see page 36)

Unless specified otherwise, receivers/DVRs

in the following wiring diagrams are not

SWM-compatible.

IMPORTANT!

Wiring Diagrams

Figure 46 SWM-Compatible Receivers/DVRs

*NOTE:

Unlike other DVRs, the HR34 Home Media

Center uses five tuners. Therefore, if you connect this
DVR, be sure to reserve five tuners instead of two.
Refer to the DVR’s manual for complete wiring
details.

Receivers

DVRs

H20

HR21, HR21 Pro

H21

HR22

H22

HR23

H23

HR24

H24

HR34/HMC*

H25

R16

D12

R20

D13

R22

Appendix

Содержание TracVision HD11








































Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды

KVH Industries TracVision HD11, Руководство по установке

Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды