KVH Industries TracVision HD11 Скачать руководство пользователя страница 21

Страница: 21 / 39

Follow the steps below to mount the ACU(s) and

SmartSwitch (if equipped).

ACU Rack Mounting

Attach the strain-relief bracket to the ACU, as

shown in Figure 26. Using a #1 Phillips

screwdriver, secure the bracket in place using

four #6-32 screws and #6 washers (supplied

in the kitpack).

Secure the ACU to the rack using four M6

screws and washers (see Figure 27).

ACU Horizontal Mounting

Using a #1 Phillips screwdriver, remove the

six #6-32 screws securing the rack mounting

brackets to the ACU (see Figure 28).

Using a #1 Phillips screwdriver, attach the

two horizontal mounting brackets to the sides

of the ACU using four supplied #6-32 screws

and #6 washers (see Figure 29). You can

attach the brackets to either the top or bottom

of the ACU, depending on your desired

mounting location.

If you are mounting the ACU to the

underside of a shelf, attach the strain-relief

bracket to the ACU, as shown in Figure 26.

Using a #1 Phillips screwdriver, secure the

bracket in place using four #6-32 screws and

#6 washers (supplied in the kitpack).

NOTE:

The ACU does not require a strain-relief

bracket when mounted to the top of a horizontal
surface.

Using fasteners appropriate for the mounting

surface, secure the ACU to the mounting

surface using the four mounting bracket

holes.

Mount Belowdecks Equipment

Figure 26 ACU Strain Relief Bracket

Figure 27 ACU Rack Mounting

Figure 28 ACU Rack Mounting Bracket Removal

Figure 29 Horizontal Mounting Brackets

Strain-Relief
Bracket

#6-32

Screw (x4)

#6 Washer
(x4)

CONTROL UNIT

CHANGE

EXIT

ANTENNA

POWER

T R A C K I N G S A T S

D I R E C T V 9 9 / 1 0 1 / 1 0 3

Mounting
Hole (x4)

M6 Screw

and Washer (x4)

Rack Mounting
Bracket (x2)

#6-32 Screw (x6)

Horizontal
Mounting
Bracket (x2)

#6-32 Screw and

#6 Washer (x4)

Содержание TracVision HD11








































Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды

KVH Industries TracVision HD11, Руководство по установке

Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды