KVH Industries TracVision HD11 Скачать руководство пользователя страница 25

Страница: 25 / 39

Connect the Power/Data Cable

Follow the steps below to connect the antenna’s

power/data cable to the ACU.

Connect the power/data cable wires to the

large terminal strip connector (supplied in
the kitpack), as shown in Figure 39.

Plug the terminal strip connector into the rear

of the ACU (see Figure 39).

Connect the ring terminal of the grounding

sleeve’s ground wire to the grounding screw

on the rear of the ACU (see Figure 39).

If you are installing two antennas, repeat the

steps above to connect the second antenna’s

power/data cable.

Connect NMEA Input

Follow the steps below to connect the NMEA

input to the ACU.

Connect the vessel’s NMEA 0183 Talker

wires to the small terminal strip connector

(supplied in the kitpack), as shown in

Figure 39. Make sure the device is configured

to transmit $--HDT messages at 4800 baud to

provide true heading to the system.

NOTE:

The antenna requires a NMEA 0183 input; it

is not compatible with the NMEA 2000 standard.

Plug the terminal strip connector into the rear

of the ACU (see Figure 39).

The diagram refers to wires by

body color/

stripe colo

r. For example, “Brown/White”

means the brown wire with the white stripe.

IMPORTANT!

Continued

Wire Belowdecks Equipment

Figure 39 Power/Data Cable Wiring

Fuse 3.15A 250V ~ Fast Acting

Ethernet

SmartSwitch

Controller

Maintenance

RS232

To Antenna

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device must not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Red (+48V)

Blac

(Gnd)

White/Gr

ay/White

White/Or

nge

ange/White

White/Bro

Bro

n/White

White/Blue

Blue/White

White/Gr

een

een/White

Red/Or

ange

ange/Red

Red/Gr

een

een/Red

B (+)

A (–)

Wire Color/Stripe Color

WiFi

NMEA

Single Phase AC Input 100-240V ~ 200W MAX 50/60 Hz

KVH and TracVision are registered
trademarks of KVH Industries, Inc.

Tested to comply
with FCC Standards

Meets requirements

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

13 14 15 16

Terminal Strip

Blue/White

White/Blue

Brown/White

White/Gray

Gray/White

White/Orange

Orange/White

White/Brown

Red (+50V)

Black (Gnd)

ACU

Antenna

Orange/Red

Red/Orange

Green/White

White/Green

Green/Red

Red/Green

Power/Data

Grounding
Sleeve

Ground Wire

NMEA 0183 Talker

(customer-supplied)

True Heading ($--HDT)

Содержание TracVision HD11








































Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды

KVH Industries TracVision HD11, Руководство по установке

Результаты поиска

Содержание TracVision HD11

Отзывы:

Похожие инструкции для TracVision HD11

Бренды по названию

Популярные бренды