manualshive.com logo in svg

Kval 990-HQ, Руководство по эксплуатации

Поделиться
Скачать
Kval 990-HQ Скачать руководство пользователя страница 61

Hinge Spec Group

White boxes displays the loaded Pre-
set. Adjustments may be made by 
changing the data in the box. 

Speed:

 Select speed of the router. The 

range is 100% to 20%. The speed can 
be change during process of machin-
ing.

Pre-Drill Pattern: 

Select 

Pre-Drill 

but-

tons to down load pre-drill parame-
ters. Also the ability to turn on or off 
this function.
To set 

Pre-Drill 

parameters, 

see “About the Pre-Drill Screen” on page 2-55. 

 

Length: 

Displays the length of the 

hinge pocket.

Overall Height: 

Displays the height 

(vertical) of the hinge pocket.

Backset:

 Displays the space between 

the door edge and hinge.

Depth: 

Displays depth (Z axis) of the 

hinge pocket.

Radius: 

Displays the rounded corners 

of the hinge pocket.

Reveal: 

The Reveal is set by the 8 Shooter Pins and the H-Block Spacers.

Overall Height

Backset

Radius

Reveal

Length

   Main Screen

2-33

990-HQ Operation Manual

Содержание 990-HQ





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды