manualshive.com logo in svg

Kval 990-HQ, Руководство по эксплуатации

Поделиться
Скачать
Kval 990-HQ Скачать руководство пользователя страница 23

   Getting Help from KVAL

1-15

990-HQ Operation Manual

• What is the extent of the failure/reason for return? What are the relevant error mes-

sages or error codes?

• How long did it operate?
• Did any other items fail at the same time?
• What was happening when the unit failed (e.g., installing the unit, cycling power, 

starting other equipment, etc.)?

• How was the product configured (in detail)?
• Which, if any, cables were modified and how?
• With what equipment is the unit interfaced?
• What was the application?
• What was the system environment (temperature, spacing, contaminants, etc.)?

3. 

Call Kval customer support for a Return Material Authorization (RMA). When you 

call:

• Have the packing slip or invoice numbers available.
• Have the documented reason for return available.

4. 

Send the merchandise back to Kval. 

• Make sure the item(s) you are returning are securely packaged and well protected 

from shipping damage

• Include the packing slip or invoice numbers.
• Include the documented reason for return.
• Include the RMA number with the parts package.

Содержание 990-HQ





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды