Kval 990-HQ Скачать руководство пользователя страница 30

Страница: 30 / 92

The 990-HQ Process Summary

2-2

990-HQ Operation Manual

The 990-HQ Process Summary

The

990-HQ

machines hinge pockets on both a door and a jamb and then attaches hinges to them.

While the hinge process takes place a door lock and face plate is drilled.

This machine can rout four hinge pockets

Feeding the door to the

990-HQ

is an

ON-12HQ c

onfigured as a feeder. Some key assemblies on the

990-HQ.

• Cut a hinge pocket on a door and jamb (Carriage Assembly).
• Drill pilot holes for the hinge screws (Carriage Assembly).
• Apply hinges (8 Shooter).
• Attach the hinges with screws (8 Shooter).
• Cut a lock and lock plate (Back Section).

Note:

Along with automatic control, manual control functions can be implemented. The machine

also accommodates mixed stacks and automatic door positioning with a two-speed feed belt sys-
tem.

Machine Orientation

The

Front Section

refers to the side of the machine with the operator’s station, and includes the

three Eight-Shooter heads, the front router motors, the pre-drills and chisels.

The

Back Section

refers to side of the machine that routs the faceplate, bores the lock, and drills

for the bolt.

In-Feed:

The end of the machine (and its respective parts) that receives incoming doors.

Typical Production Line Layout

The

990-HQ

can be paired with different feeder and stacker model numbers. This manual assumes

the

ON-12HQ

as a feeder. The feeder is addressed in a separate manual.

ON-12HQ
Feeder

990-HQ Door Hanger

FIGURE2- 1.

The 990-HQ Door Hanging System

Содержание 990-HQ





























































































Результаты поиска

Содержание 990-HQ

Отзывы:

Похожие инструкции для 990-HQ

Бренды по названию

Популярные бренды

Kval 990-HQ, Руководство по эксплуатации

Результаты поиска

Содержание 990-HQ

Отзывы:

Похожие инструкции для 990-HQ

Бренды по названию

Популярные бренды