Kval 990-HQ Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 92

background image

Safety First!

1-5

990-HQ Operation Manual

Safety First!

This machine is a powerful electro-mechanical motion control
system. You should test your motion system for safety under
all potential conditions.

Failure to do so can result in dam-

age to equipment and/or serious injury to personnel.

Safety Sheet Sign-Off Sheet

At the end of this chapter, there is a safety sign-off sheet. It lists personnel and machine safety cri-
teria to understand before operating the machine. It is highly recommended that personnel operat-
ing, working on a machine meet the criteria listed in this sheet. It is recommended the sheet be
signed and kept for records. See “Safety Sign-Off Sheet” on page 1-19.

Safety Terminology of Labels

In addition to the nameplate, KVAL machines may have other warning labels or decals that pro-
vide safety information to operators. Safety labels should be clearly visible to the operator and
must be replaced if missing, damaged, or illegible.

There are three types of warning labels or decals:

•

DANGER

me if the danger is not avoided, it will cause death or serious injury.

•

WARNING

me if the warning is not heeded, it can cause death or serious injury.

•

CAUTION

me if the precaution is not taken, it may cause minor or moderate

injury.

Safety Guidelines

In addition to the caution and warning labels affixed to this machine, follow the guidelines below
to help ensure the safety of equipment and personnel.

Ensure that all employees who operate this machine
are aware of and adhere to all safety precautions
posted on the machine and are trained to operate this
machine in a safe manner.

Training

«
...
11
12
13
14
15
...
»

Содержание 990-HQ





























































































Отзывы:

Нет отзывов

Похожие инструкции для 990-HQ

Бренд: ABB Страницы: 27

Бренд: Balanced Body Страницы: 4

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: IBS Scherer Страницы: 64

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды