10
Technical passporT
english
gas hob
Â
Remember that the earth wire
must not be interrupted by the circuit-
breaker.
Â
Alternatively, the electrical
connection may also be protected by
a high sensitivity differential circuit
breaker.
Â
You are strongly advised to x
the relative yellow-green earth wire to
an ef cient earthing system.
6.4. GAS CONNECTION
These instructions are prepared for
specialist personnel having
required
competence, the installation of the
equipment
should be suitable as per
the applicable standards.
All gas related works should be
conducted when the electric connection
was cut.
The value plate on the hob indicates
the gas type intended to be used for use
with the hob. Connection to the main
gas course or gas type shall be realized
after controlling the adjustment as
per the gas type. Connection to the
main gas source or gas cylinder shall
be conducted after checking the
adjustment according to the proper
gas type. If it is set properly look at the
following paragraphs:
Note that the LPG hoods should
have standarts stamp and 300 mmSS
(29,4 mbar) of outlet pressure.
Natural gas pressure is 200 mmSS
(19,6 mbar). Please consult the
authorized service for conversion to
natural gas or LPG.
Use only piping, gaskets or stamp as
per the applicable national standards.
In some countries where conic
connections are obligatory, conic
connection is provided. In such a case
the conic connection part should be
connected to the unit.
If the unit will be connected to a
exible hose, the length of the hose
shall not exceed 120 cm.
Before starting works related to gas
installation, please cut the gas supply.
Make the connection so that
no pressure will be applied on the
connection records and piping. Make
sure that the pipe will not cause any
clogging or contact with the sharp
corners.
Note that the gas hose will not be
laid through hot areas.
NOTE: Replace the gas hose of your
hob at 4 to 5 years even if it will be
undamaged.
NOTE: Check whether any gas
leakage after the connection with soap
and water. Do not ever use ame.
Make sure that no additional weight
to be applied on the gas hose.
And apply the following order for
installation:
1. In the order; male adaptor
cylindrical, gasket, female gas adaptor,
FIG. 4
FIG. 5
Содержание FV6TGRZ
