KUHN FC883RA Скачать руководство пользователя страница 97

Страница: 97 / 104

Trouble shooting guide

Mower conditioner

FC883RA

TROUBLE SHOOTING GUIDE

Problem

Cause

Remedy

Uneven stubble.

Dull or broken knives.

Replace knives.

Knives not installed correctly.

Make sure the arrow on the

knife upper face is pointing in
the disc's direction of rotation.

Too low PTO speed (rotational

frequency).

Increase speed to 1000 min

-1

Soil build up in front of the

cutterbar.

Too much cutterbar down

pressure.

Increase accumulator

pressure.

Very wet working conditions.

Adjust main frame height with

regards to the ground.

Bad ground contour

adaptation.

Incorrect main frame setting.

Adjust main frame height with

regards to the ground.

Excessive ground speed.

Reduce ground speed.

Insufficient ground pressure.

Reduce accumulator pressure.

Obstruction of conditioning

rotor.

Insufficient rotor speed

(rotational frequency).

Check that the rotor drive belts

are correctly tensioned.

Too low PTO speed (rotational

frequency).

Increase speed to 1000 min

-1

Swath shields too closed.

Open swath shields.

Machine requires too much pull

power.

Too much cutterbar down

pressure.

Adjust the mowing unit ground

pressure.

Содержание FC883RA









































































































Результаты поиска

Содержание FC883RA

Отзывы:

KUHN FC883RA, Руководство оператора, Страница: 97 / 104

Результаты поиска

Содержание FC883RA

Отзывы: