KUHN FC883RA Скачать руководство пользователя страница 34

Страница: 34 / 104

Mower conditioner

FC883RA

Putting into service

Description of the connection

The control box is connected to:

- A tractor 3-pin socket.
- A machine wiring harness on the hydraulic valve

bank.

For tractors not fitted with a 3-pin socket, a wiring

harness can be ordered under Part no. N01602A0.

Connect the wiring harness directly to the battery

terminals respecting the polarities.

The wiring harness is fitted with a 15 Amp ATO type fuse

Part no. 83233017.

2. Coupling and uncoupling

The machine adapts to tractors fitted with a 3-point hitch

coupler category 2 or 3.

Description of coupling elements

- A PTO shaft 1 3/4’’ 6 splines (1).
- A release cord (2).
- 2 hydraulic hoses (3) pressurize the hydraulic valve

bank.

- 2 hydraulic hoses (4) pressurize the offset cylinder.
- 1 hydraulic hose (5) to pressurize the brake actuation

system.

- A 7-pin electric plug for the electrical signalling

equipment (6).

- 1 hydraulic hose for adjusting the front mowing unit

suspension.

- A 19-pin plug for the hydraulic valve bank (7).

Never connect battery charger or perform
welding tasks without having previously
disconnected the control box.

Do not connect the wiring harness to the
starter connections.
Check that the connectors are in a good
condition and clean.

Содержание FC883RA









































































































Результаты поиска

Содержание FC883RA

Отзывы:

KUHN FC883RA, Руководство оператора, Страница: 34 / 104

Результаты поиска

Содержание FC883RA

Отзывы: