KUHN FC883RA Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 104

KUHN FC883RA Скачать руководство пользователя страница 80

Mower conditioner

78

FC883RA

Maintenance and storage

Central gearbox

- Lower and lock parking stands (1).
- Place the machine in working position.
- Remove filler plug (2).
- Place a container of sufficient capacity under drain

plug.

- Remove drain plug (3).
- Allow oil to drain completely.
- Wait for dripping to stop.
- Clean and reinstall drain plug (3) and its washer.

replace them if necessary.

- Pour the correct oil quantity and quality through the

opening of the filler plug (2).

- Check central gearbox oil level.
- The oil level must reach the medium level of sight

glass (4).

Before draining oil, operate the machine for a
few minutes so that the oil warms up.

The angle gearbox is lubricated with 5.5 L (1.45 US gal) of SHELL SPIRAX A extreme-pressure oil for
mechanical transmissions with viscosity grade SAE80W90 and API grade GL5.
When draining and refilling, it is recommended to use either a mineral base oil with viscosity grade
SAE80W90 and API grade GL5, or a synthetic base oil, type PAO (Poly-Alpha-Olefins) with a viscosity
grade equivalent to SAE80W90.

Maximum level: (a).
Minimum level : (b).

«
...
78
79
80
81
82
...
»

Содержание FC883RA









































































































Отзывы:

Нет отзывов