KUHN FC883RA Скачать руководство пользователя страница 96

Страница: 96 / 104

Mower conditioner

FC883RA

Maintenance and storage

5. Storage

At the end of each season

- Clean the machine thoroughly.
- Drain all gearboxes and cutterbar and refill with new

oil: See section ’’Lubrication’’.

- Touch up paint if necessary.
- Put the machine under cover in a dry place.
- Inspect and replace worn knives and bolts: See

section "Inspection of knives and securing elements".

- Inspect and replace worn or damaged fingers on the

conditioning rotor.

- Slacken V-belts and check their condition.
- Depressurize all hydraulic functions.

At the start of each season

- Read through the operator's manual again.
- Pressurize the hydraulic circuit.
- Check the condition of the friction slip clutch: See

section ’’Secondary PTO shaft’’.

- Inspect and replace worn knives and bolts: See

section ’’Cutterbar’’.

- Check that all nuts and bolts are sufficiently tightened.
- Retension V-belts.
- Check belt guard condition and if it is firmly secured in

place.

- Inspect and replace worn or damaged fingers on the

conditioning rotor.

Содержание FC883RA









































































































Результаты поиска

Содержание FC883RA

Отзывы:

KUHN FC883RA, Руководство оператора, Страница: 96 / 104

Результаты поиска

Содержание FC883RA

Отзывы: