KUHN FC883RA Скачать руководство пользователя страница 19

Страница: 19 / 104

Safety

Mower conditioner

FC883RA

Description of safety decals

Operating instructions (1)

The operator's manual contains all the information

necessary for using the machine safely. It is imperative
to read and comply with all instructions.

Working on the machine (2)

Before leaving the tractor or before adjusting,

maintaining or repairing the machine, disengage the
PTO drive, turn off the engine, remove ignition key and
wait until all moving parts have come to a complete stop
and apply park brake.

Danger accumulator (3)

The hydraulic accumulator contains gaz and oil under

pressure. To park the machine or carry out maintenance
work, conform with the instructions given in the
operator's manual

Projections (4)

Stones and other debris projected by the moving parts

can travel a long distance. The protection covers must
always be in position and in good condition. Always stay
at a safe distance from the machine.

Содержание FC883RA









































































































Результаты поиска

Содержание FC883RA

Отзывы:

KUHN FC883RA, Руководство оператора, Страница: 19 / 104

Результаты поиска

Содержание FC883RA

Отзывы: