background image

Mower conditioner

8

FC243

Safety

„

Precautions to take before using the 
machine

Do not wear loose clothing which could become caught

up in moving parts.

Wear the appropriate protective clothing for the work in

hand (gloves, shoes, goggles, helmet, ear-protectors,
etc.).

Make sure that all operating controls (ropes, cables,

rods, etc) are placed so that they cannot be set off
accidentally, risking accident or damage.

Before operating the machine, check tightness of nuts

and bolts, particularly on fixing elements (tines, forks,
blades, knives, etc). Retighten if necessary.

Before operating the machine, ensure that all the safety

guards are firmly in place and in good condition.
Immediately replace any worn or damaged guard.

„

Precautions when driving

Precision steering, tractor adherence, road holding and

efficient braking are influenced by the type of implement,
weight, ballast of front axle, ground or road conditions. It
is therefore of the utmost importance to be cautious in
every given situation.

Groundspeed must be adapted to ground conditions as

well as to roads and paths. Always avoid abrupt changes
of direction.

Be particularly cautious when turning corners, paying

attention to machine overhang, length, height and
weight.

Never use a narrow track tractor on very uneven or

steeply sloping ground.

Never leave the tractor seat while the machine is

operating.

Carrying people or animals on the machine when

working or in transport is strictly forbidden.

Содержание FC243









































































Отзывы: