Kühling&Kühling HT500 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 27

background image

exceeding the speciﬁed maintenance
intervals
cases of disaster and force majeure

Ordering wear and spare parts and material

Wear parts must meet the technical speciﬁcations deﬁned by Kühling&Kühling. Kühling&Kühling
original parts are subject to rigid requirements and meet these standards. A complete list of available
wear and spare parts and suppliable materials can be found at

our web shop

together with an order

form.

Life cycle

Find everything you need to know after you ordered your HT500 3D Printer in the following
paragraphs. From the day of your invoice until the day you want to dispose of the apparatus and
anything in between is explained here.

Delivery

The HT500 3D Printer arrives at your place fully assembled and can be

commissioned

directly after

setting it up and connecting the power supply.
The 3D Printer is delivered in a wooden transport box on a palette. It is advisable to leave the HT500
packed and on the palette until moving it to its ﬁnal installation site for commissioning.
At the installation site, unpack the HT500 according to the information in the accompanying

Quick

Start Guide

.

Dispose of the packaging in accordance with the local waste disposal regulations.
After unpacking, inspect the apparatus for:

damage in transit
completeness of the delivery (compare delivery note)

If you notice any deviants, please immediately inform the hauler and the

manufacturer

. Do not put

the HT500 to use with defective parts.

Transport

To avoid injuries and property damage observe the following notes when transporting the HT500:

The apparatus' weight exceeds 50 kg. Always carry it two by two.
Keep the HT500 horizontal to avoid damaging internal parts.
Avert shock loads to the housing.

The HT500 has been designed for stationary

«
...
2
3
4
5
6
...
»

Содержание HT500




























Отзывы:

Нет отзывов

Похожие инструкции для HT500

Бренд: Oki Страницы: 222

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 160

Бренд: WANHAO Страницы: 5

Бренд: Wang Страницы: 24

Aficio SP4100N-KP

Бренд: Ricoh Страницы: 4

Бренд: Citizen Страницы: 80

3500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 6

B-470-QQ Series

Бренд: TEC Страницы: 32

Бренд: Z Corporation Страницы: 70

CraftBot PlusPro

Бренд: CraftUnique Страницы: 2

Бренд: 3D Systems Страницы: 72

Бренд: Infinite Peripherals Страницы: 2

Бренд: 3D Systems Страницы: 83

Бренд: Brother Industries Страницы: 22

Бренд: Sharp Страницы: 71

Бренд: twotrees Страницы: 32

Бренд: Citizen Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды