Kubota RT120Q Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 219

Kubota RT120Q Скачать руководство пользователя страница 95

Transport - 94

RT120Q Operator’s Manual

Tie Down

Traversing Trencher

Lower trencher to trailer deck and chain at
attachment frame. Ensure chains are tight
before transporting.

Combo

Lower attachment to trailer deck and chain at
attachment frame and vibrator box. Make sure
chains are tight before transporting.

IMPORTANT:

If trencher is equipped with

a trench cleaner, ensure that trench
cleaner shoe is fully up and extra bolt
(found in operator’s manual compartment)
is installed in appropriate hole for
additional support.

NOTICE:

•

Engage attachment stow lock and swing
lock devices in addition to securing at
tiedowns.

•

Unsecured plow can swing outside the
trailer and become a traffic hazard. Lower
plow and chain to trailer deck before
hauling.

•

If trencher is equipped with a trench
cleaner, ensure that trench cleaner shoe
is fully up and extra bolt (found in
operator’s manual compartment) is
installed in appropriate hole for additional
support.

«
...
93
94
95
96
97
...
»

Содержание RT120Q




























































































































































































































Отзывы:

Нет отзывов