Kubota RT120Q Скачать руководство пользователя страница 182

Страница: 182 / 219

RT120Q Operator’s Manual

Service - 181

500 Hour

Trencher

Adjust Headshaft Bearing

Adjust headshaft bearing every 500 hours.

To adjust:

Remove cover. Remove bolts attaching
trenching attachment motor to gearbox.

Remove bolt and washers in left end of
headshaft.

Support gearbox with hoist and slide it off
headshaft.

Install spacer (p/n 184-044) in place of
gearbox while checking bearings.

Replace bolt on end of headshaft.

Remove chain from headshaft sprocket.

Turn chain sprocket until headshaft sprocket turns.If it turns easily, remove a shim.

Plow

Change Plow Vibrator Oil

Change plow vibrator oil every 500 hours. If
normal operating temperature exceeds 100°F
(38°C), change plow vibrator oil every 250 hours.

Drain oil at drain plug (2). Replace plug and move
plow vibrator to horizontal position. Add MPL at fill until oil is halfway up sight glass (1).

Refill capacity is 4

qts (3.8 L).

Hot parts may cause burns. Do not touch until
cool or wear gloves.

Содержание RT120Q




























































































































































































































Результаты поиска

Содержание RT120Q

Отзывы:

Kubota RT120Q, Руководство оператора, Страница: 182 / 219

Результаты поиска

Содержание RT120Q

Отзывы: