background image

HYDRAULIC UNIT

82

B

Control Switch

1. Front hydraulic valve main switch

Push the front hydraulic valve main switch (1) to
engage the front hydraulic valve.
A light on the switch will illuminate to indicate that the
front hydraulic valve is on, and to enable the activation
switch (2).

2. Activation switch

(1) When pressing the "A" button, hydraulic oil will

come out of the port A and return through the port
B as long as the switch is pressed.

(2) When pressing the "B" button hydraulic oil will

come out of the port B and return through the port
A as long as the switch is pressed.

3. Push the front hydraulic valve main switch again to

disengage the front hydraulic valve, and the light of the
front hydraulic valve main switch will turn off.

To avoid personal injury:

A

Valve lock does not lock out switch operated
third-function hydraulics, which are active
when the key switch and the front hydraulic
valve main switch are ON.

B

Remote Control Coupler Connecting and 

Disconnecting

To avoid personal injury or death:

A

Stop the engine and relieve pressure before
connecting or disconnecting lines.

A

Do not use your hand to check for leaks.

C

Relieve Hydraulic Pressure

1. Move the key switch to the "RUN" position.

A

Don't start the engine.

2. Push the front hydraulic valve main switch "ON".
3. Press the activation switch A and B several times.
4. Push the front hydraulic valve main switch "OFF".
5. Turn the key switch to the "OFF" position.

C

Connecting

1. Clean both couplers.
2. Remove dust plugs.
3. Insert the implement coupler to the tractor hydraulic

coupler.

4. Pull the implement coupler slightly to make sure

couplers are firmly connected.

C

Disconnecting

1. Lower the implement first to the ground to release

hydraulic pressure in the hoses.

2. Clean the couplers.
3. Relieve hydraulic pressure.

Pull the hose straight from the hydraulic coupler to
release it.

4. Clean oil and dust from the coupler, and then replace

the dust plugs.

A

Your local KUBOTA Dealer can supply parts to adapt
couplers to hydraulic hoses.

(1) Front hydraulic valve main switch
(2) Activation switch

(C) Front hydraulic valve main switch "OFF"
(D) Front hydraulic valve main switch "ON"

Содержание L47TL
































































































































































Отзывы: