Kubota L47TL Скачать руководство пользователя страница 68

Страница: 68 / 159

OPERATING THE TRACTOR

Range Gear Shift Lever (L-M-H)

The range gear shift can only be shifted when the tractor
is completely stopped and the speed control pedal is in
the neutral position.

IMPORTANT:

To avoid transmission and shift linkage damage when
shifting:

Completely stop the tractor using the brake pedals.

Do not force the range gear shift lever.

If it is difficult to shift the lever into L, M, or H from
neutral position:
On slopes be sure to set the parking brake before
starting the procedure.
(1) Slightly depress the speed control pedal to rotate

the gears inside of the transmission.

(2) Release the speed control pedal to the neutral

position.

(3) Wait for a moment and then shift the lever.

The range gear shift number being selected appears
on the display.

(1) Range gear shift lever (L-M-H) (H) "HIGH"

(M) "MIDDLE"
(L) "LOW"
(N) "NEUTRAL POSITION"

(1) Range gear shift number (H-M-L)

N: "NEUTRAL"

Содержание L47TL
































































































































































Результаты поиска

Содержание L47TL

Отзывы:

Kubota L47TL, Руководство оператора, Страница: 68 / 159

Результаты поиска

Содержание L47TL

Отзывы: