Kubota L47TL Скачать руководство пользователя страница 80

Страница: 80 / 159

OPERATING THE TRACTOR

REVERSING THE SEAT

The seat is reversible for backhoe operation. Follow the
procedure below to turn the seat around.
1. Unlock the seat lock lever.

2. Turn the seat to counterclockwise for backhoe

operation.
The seat is automatically locked at the backhoe
position.

When rotating seat, do not hit any controls or levers.

3. For tractor driving position, unlock the seat lock lever

and turn the seat clockwise.

See "Operator's Seat" in "STARTING" when using
seat in driving position.

To prevent damage to the lock lever or to release the
seat lock properly, do not attempt to pull up the lock
lever with extreme force while sitting on the seat. First
lift yourself from the seat, and then pull up the lock
lever.

(A) "TRACTOR DRIVING POSITION"
(B) "BACKHOE POSITION"

(1) Seat lock lever

(A) "UNLOCK"

Содержание L47TL
































































































































































Результаты поиска

Содержание L47TL

Отзывы:

Kubota L47TL, Руководство оператора, Страница: 80 / 159

Результаты поиска

Содержание L47TL

Отзывы: