Kubota CKTGL11000 Скачать руководство пользователя страница 6

Страница: 6 / 62

SAFETY PRECAUTIONS

ENGL

ISH

CAUTION

To avoid personal injury:

Electric shock and fire hazard: Do not connect
the machine to any indoor (commercial) power
outlet.

Electric shock and injury hazard: Do not allow
children to run the machine.

Electric shock and injury hazard: Turn off the
circuit breaker before starting the machine.

Injury hazard: Do not touch the muffler.

Injury hazard: Do not run the machine tilted.

Injury hazard: Do not move the machine while it
is running.

Fire hazard: Stop the engine before adding fuel.

Fire hazard: Do not enclose the machine, nor
cover it with a box or the like.

Fire hazard: Pay attention to the type and
amount of fuel.

Do not get the warning label dirty or peeled off.

Be sure to hand over the operation manual to
any other operator.

Electric shock hazard: Ground the machine
using the ground terminal on the control panel.

Содержание CKTGL11000































































Результаты поиска

Содержание CKTGL11000

Отзывы:

Kubota CKTGL11000, Руководство оператора, Страница: 6 / 62

Результаты поиска

Содержание CKTGL11000

Отзывы: