manualshive.com logo in svg

Kubota CKTGL11000, Руководство оператора, Страница: 22 / 62

Поделиться
Скачать
Kubota CKTGL11000 Скачать руководство пользователя страница 22

10

PREPARATION TO SUPPLY THE ELECTRIC POWER

ENGL

ISH

PREPARATION TO SUPPLY THE ELECTRIC POWER

The end user, equipment owner or operator must
contact his local, state, county or municipal electric
code department to determine the approved generator
grounding method to be used in his application or
location.
Recommendations in the NEC (National Electrical
Code), NFPA (National Fire Protection Association),
AUSTRALIAN STANDARDS and OSHA (Occupational
Safety and Health Administration) regulations must be
followed to assure compliance and safe operation.
Always be sure to ground (earth) the generator
terminals to comply with the local, state, national or
OSHA requirements.

One possible connection method for construction site
use is as follows:

APPLICATION RANGE

You can operate the GL-series generator in the
following range.

A

Keep an inverter load below 50% of the generator
capacity.

A

Make sure that total active mercury lamp load is
below 30% or so of the generator capacity. Turn on
the mercury lamps one by one. Be careful not to turn
off the lamps and on again immediately. The
generator voltage may rise to extremely high levels
and the AVR may get damaged.

A

Before turning on the lamps again, wait for 10
minutes or so until the lamps cool down enough.

A

The data shown above is only a guideline to
approximate load capacities and may vary from
generator model to generator model, with different
types of loads at rated outputs. These values may be
different from actual applications because of the
input characteristics peculiar to each load. 

1. Generator grounding

(1) Generator ground

 terminal

(A) #6AWG

Flexible copper ground
connection

(B) Metal ground rod or building

cold water pipe system per
N.E.C. code

2. Recommended capacity of electrical

devices

Typical

Apparatus

Light and

heaters

Commutator

motor

Induction

motor

GL6000

5.5 kW

2.8 kW

0.8 kW

GL7000

6.5 kW

3.3 kW

0.8 kW

GL9000

8 kW

4.0 kW

1.2 kW

GL11000

10 kW

5.0 kW

1.6 kW

Содержание CKTGL11000































































Отзывы:

Нет отзывов