manualshive.com logo in svg

Kubota CKTGL11000, Руководство оператора, Страница: 24 / 62

Поделиться
Скачать
Kubota CKTGL11000 Скачать руководство пользователя страница 24

12

CONNECTING THE LOAD

ENGL

ISH

CONNECTING THE LOAD

B

Connection Notes

WARNING

To avoid personal injury:

A

Before the generator can be
connected to a building’s electrical
system, a licensed electrician must
install an isolation (transfer) switch
in the building’s main fuse box. The
switch is the connection point for
generator power and allows
selection of generator or main line
power to the building. This will
prevent the generator from charging
the main power line (backfeeding)
when the main power supply has
failed or has been turned off for line
repair. Backfeeding can electrocute
or injure line maintenance
personnel. Also, generator and
building electrical system damage
can occur when normal operating
power returns if unit is used without
an isolation switch.

1. Avoid connecting the generator to commercial

power outlet.

2. Avoid connecting the generator in parallel with any

other generator.

B

Connecting the Load (Terminal output 
Model)

WARNING

To avoid personal injury:

A

Connect or disconnect the load to
the AC receptacles or terminals only
when the engine is stopped.

A

For your safety, close the terminal
cover after connecting the load.

A

For your safety, secure the cover
with the lock bolts.

1. Turn OFF the circuit breaker on the control panel.
2. Connect  the load to the A.C. output terminals.
3. Be sure to close the terminal cover after connecting

the load.

(1) Circuit breaker
(2) Terminals (output)
(3) Cover lock bolt

Содержание CKTGL11000































































Отзывы:

Нет отзывов