manualshive.com logo in svg

Kubota CKTGL11000, Руководство оператора, Страница: 32 / 62

Поделиться
Скачать
Kubota CKTGL11000 Скачать руководство пользователя страница 32

20

OPERATING THE GENERATOR

ENGL

ISH

A

Do not use ether or any starting fluid for starting the
engine, or severe engine damage will occur.

A

See "Cold Weather Starting" section as to the
preheating times.

A

Do not run the starter motor continuously for more
than 10 seconds at a time, or it may damage the
starter. If the engine fails to start, wait for about 30
seconds and try again.

A

Be sure to warm up the engine, not only in winter, but
also in warmer seasons. An insufficiently warmed-up
engine can shorten its service life.

3. Ensure that the fuel lever is set to the

"OPEN" Position.

(1) Fuel lever
(2) Fuel filter pot

(A) "OPEN"

4. Insert the key into the main switch and

turn it "ON".

5. Check the battery charge lamp and oil

pressure lamp are ON.

(1) Water temperature lamp
(2) Oil pressure lamp
(3) Battery charge lamp
(4) Glow timer lamp

6. Turn the key to "PREHEAT" position.

7. Turn the key to the "START" position

and release when the engine starts.

(1) Starter switch (Key)

(A) "OFF"
(B) "ON"
(C) "PREHEAT"
(D) "START"

8. Check to see that the battery charge

lamp, oil pressure lamp and water
temperature lamp are OFF.

9. Check the warning lamps.

Whenever the engine stops automatically
during operation, correct the problem
before restarting the engine.

Содержание CKTGL11000































































Отзывы:

Нет отзывов