Kubota CKTGL11000 Скачать руководство пользователя страница 51

Страница: 51 / 62

TROUBLESHOOTING

ENGL

ISH

Engine

If you have any questions, contact your KUBOTA dealer.

Trouble

Cause

Countermeasure

Not started.

Not turned or slow

turning.

Battery trouble.

•

Replacement of battery.

Insufficient battery charge.

•

Recharge battery.

Slow turning at cold circumstance due to

high viscosity of engine oil.

Fuse blown out (Slow blow fuse)

•

Replace engine oil to D5W40 or

D10W30 for cold.

•

Replace fuse.

Terminal cover open.

•

Close terminal cover. Fix terminal cover

with panel lock bolts.

Normal turning,

but not started.

Fuel shortage.

•

Refuel.

Fuel does not flow.

•

Check fuel filter. If filter is dirty, replace.

•

Check fuel tank. Remove the settled

impurities or moisture.

Air and water are contained in fuel supply

line.

•

Check pipe and fastening clamp. If any

damage exists, replace or repair.

•

Relieve air.

•

Remove water inside of fuel tank and

filter.

Injection pipe is loosened.

•

Re-tighten.

Engine starts but stops immediately.

Engine oil shortage.

•

Add engine oil to upper limit of gauge.

Rotation is irregular.

Fuel shortage.

•

Refuel.

Fuel does not flow.

•

Check fuel filter. If filter is dirty, replace.

•

Check fuel tank. Remove the settled

impurities or moisture.

Air and water are contained in the fuel

supply line.

•

Check pipe and fastening clamp. If any

damage exists, replace it, or repair.

•

Relieve air.

•

Remove water inside of fuel tank and

filter.

Injection pipe is loosened.

•

Re-tighten.

Engine suddenly stops.

Fuel shortage.

•

Refuel.

Insufficient engine oil.

•

Fill oil.

Water temperature is too high.

•

Insufficient cooling water.

•

Loosened water pump belt.

•

Blockage of radiator.

•

Fill cooling water.

•

Adjust belt tension.

•

Clean.

Terminal cover open.

•

Close terminal cover. Fix terminal cover

with panel lock bolts.

Insufficient output.

When loaded, rotation goes slow.

Choke of air cleaner element.

•

Replace air cleaner element.

Choke of fuel system.

•

Check.

Choke of fuel filter.

•

Element cleaning.

Oil deterioration.

•

Replace engine oil.

Overload.

•

Refer to generator.

Coolant leaks out.

Insufficient cooling water.

•

Fill cooling water.

Loosened fan belt.

•

Adjust belt tension.

Blockage of radiator.

•

Clean.

Exhaust gas is bad.

Choke of air cleaner element.

•

Clean air cleaner element.

Engine oil is over filled.

•

Remove oil to upper limit of gauge.

Fuel quality is bad.

•

Replace fuel with good quality fuel.

Abnormal sound

Large vibration.

Crack of vibration-proof rubber.

•

Replace.

Others.

•

Check, repair.

Содержание CKTGL11000































































Результаты поиска

Содержание CKTGL11000

Отзывы:

Kubota CKTGL11000, Руководство оператора, Страница: 51 / 62

Результаты поиска

Содержание CKTGL11000

Отзывы: