manualshive.com logo in svg

KTMED OXYPALM, Руководство оператора

Поделиться
Скачать
KTMED OXYPALM Скачать руководство пользователя страница 14

SECTION 3 – Preparation for Measurement   

 
 

KTMED Inc.                                    Model OXYPALM     

Operator’s Manual                              12

 

 

3-1 Preparation of Sensor 

Connect the sensor with its extension cable and connect opposite of the extension cable with sensor 

socket on the top of the device.   

※

 

Caution

 

Please check the compatibility of sensors with KTMED Inc. or our representative other than those KTMED

Inc. supplies in case those should be used. 

 
3-2 Turn on/ off 

Turn on the OXYPALM by pressing and holding the on/off button

  on the front of the unit for 2seconds.   

Turn off the unit by pressing and holding the on/off button

  on the front of the unit for 2seconds. FND is 

indicated as shown [Figure 8] and the power goes off. 

 [Figure 8] 

 
Initial display 

When turn on the device, all indicators are turned on for 3seconds as shown [Figure 9].   

Please check that all indicators are turned on. If an indicator is not turned on, breakdown should be 

considered. In this case, please contact with KTMED Inc directly or our representatives. 

 [Figure 9] 

 

Содержание OXYPALM




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды