KTM EXC 200 EXC Скачать руководство пользователя

Страница: 28 / 70

ENGLISH

Breather plug front fork

After every 5 hours of use for competitive racing, slacken the breather

plugs

[1]

a few turns in order to relieve excess pressure from the inside of the

fork. To do this, place the motorcycle on a stand with the front wheel lifted

off the ground. When riding the motorcycle mainly on the road, it will suffice

to have this job performed in the course of the periodical maintenance

service.

EXCESSIVE PRESSURE IN THE INTERIOR OF THE FORK CAN CAUSE LEAKS IN THE

FORK. IF YOUR FORK IS LEAKING, IT IS RECOMMENDED TO OPEN THE BREATHER

PLUGS BEFORE HAVING THE SEALS REPLACED.

Cleaning the dust sleeves of the telescopic fork

The dust-protection bellows

[2]

are to remove dust and coarse dirt particles

from the fork tube. However, after some time, dirt may also get in behind the

dust-protection bellows. If this dirt is not removed, the oil sealing rings located

behind it may start to leak.

Use a screwdriver to lift the dust-protection bellows out of the outer tubes

and slide them downward.

Clean the dust-protection bellows, outer tubes, and fork tubes thoroughly, and

oil them thoroughly with Universal oil spray (Motorex Joker 440) or engine

oil. Then, push the dust-protection bellows into the outer tubes by hand.

NO OIL MAY REACH THE FRONT TIRE OR THE BRAKE DISKS SINCE THIS WOULD

CONSIDERABLY REDUCE THE TIRE'S ROAD GRIP AND THE BRAKING EFFECT OF

THE FRONT BRAKE.

MAINTENANCE WORK ON CHASSIS AND ENGINE

Replacing fork springs

If you weigh less than 60 kg or more than 70 kg, you should install the respec-

tive fork springs. The correct spring rate is shown in the illustrations. The stan-

dard spring is shown in bold print. The type number of the telescopic fork is

embossed on the inside of the fork leg axle passage.

If you are uncertain which spring to use, contact your KTM workshop.

According to our experience, the damping rate of the compression stage can

remain unchanged. The damping rate of the rebound stage can be reduced

by a few clicks for a softer spring or increased by a few clicks for a harder

spring.

SPRING RA

RIDERS WEIGHT INCLUSIVE GEARS IN KILOGRAM

4,2 N/mm

4,4 N/mm

4,0 N/mm

for example

125 SX

Front fork

MODELL

SOFTER

STANDARD

HARDER

14187B01 125 SX

4,0 N/mm

4,2 N/mm

4,4 N/mm

14187B02 125/200 EXC, XC-W

3,6 N/mm

3,8 N/mm

4,0 N/mm

14187B27 200 XC

3,8 N/mm

4,0 N/mm

4,2 N/mm

14187B03 250 SX

4,2 N/mm

4,4 N/mm

4,6 N/mm

14187B04 250/300 EXC, XC-W

3,8 N/mm

4,0 N/mm

4,2 N/mm

14187B28 250/300 XC

4,0 N/mm

4,2 N/mm

4,4 N/mm

Содержание EXC 200 EXC







































































Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды

KTM EXC 200 EXC, Руководство пользователя

Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды