KTM EXC 200 EXC Скачать руководство пользователя

Страница: 27 / 70

ENGLISH

MAINTENANCE WORK ON CHASSIS AND ENGINE

According to our experience, the damping rate of the compression stage can

remain unchanged. The damping rate of the rebound stage can be reduced

by a few clicks for a softer spring or increased by a few clicks for a harder

spring.

Checking the basic setup of the telescopic fork

The precise riding sag of the telescopic fork cannot be determined for vari-

ous reasons. Similar to the shock absorber, smaller deviations in your weight

can be compensated by adjusting the spring preload. However, if your tele-

scopic fork bumps frequently (hard end stop during compression), you should

install harder fork springs to avoid damaging the telescopic fork and frame.

Changing the spring preload on the telescopic fork (SX models)

The telescopic forks on the SX models are equipped with a preload adjuster.

You can easily adjust the spring preload by 10 mm by turning the adjusting

screw

[1]

Turning in a clockwise direction will increase the prestress, turning in a coun-

terclockwise direction will decrease the prestress.

Changing the spring preload will not affect the rebound damping adjustment.

Generally, if the spring preload is higher, the rebound damping should also

be set higher.

STANDARD SETTING:

Unscrew the adjusting screw to the limit and then back 2 turns.

Changing the spring preload on the telescopic fork

(XC-W/EXC models)

The telescopic forks for these models must be partly disassembled to adjust

the spring preload (see WP manual). Pretension spacers are available in

heights of 1.5, 2.5 and 5 mm (see spare parts catalog). The fork springs may

not be pretensioned by more than 20 mm.

The preload adjuster used in the SX models can easily be retrofitted for the

telescopic forks of the XC-W/EXC models.

NOTE:

WP precisely adjusts the spring pressure by inserting pretension spacers.

Fluctuations in production are compensated with pretension spacers in vari-

ous heights. This can cause the fork springs in the fork legs to have different

degrees of pretension. Fork springs and pretension spacers should always stay

together.

MODELL

SOFTER

STANDARD HARDER

12187B01
125 SX

69-250

72-250

76-250

12187B02
125/200 EXC, XC-W

69-250

72-250

76-250

12187B24
200 XC

69-250

72-250

76-250

12187B03
250 SX

69-250

72-250

76-250

12187B04
250/300 EXC, XC-W

72-250

76-250

80-250

12187B25
250/300 XC

72-250

76-250

80-250

Содержание EXC 200 EXC







































































Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды

KTM EXC 200 EXC, Руководство пользователя

Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды