KTM EXC 200 EXC страница 6 Скачать руководство пользователя

Страница: 6 / 70

ENGLISH

SERIAL NUMBER LOCATIONS

Chassis number

The chassis number is stamped on the right side of the steering head tube.

Enter this number in the field on page no 1.

Engine number, engine type

The engine number and the engine type are stamped into the left side of the

engine below the engine sprocket. Enter this number on page 1.

Clutch lever

The clutch lever

[1]

is located on the left side of the handlebars. The adjust-

ing screw

[A]

is used to change the original position of the clutch lever (see

maintenance work on chassis and engine).

The clutch is hydraulically actuated and adjusts itself automatically.

Hand brake lever

The hand brake lever

[2]

is mounted on the handlebars on the right and actu-

ates the front wheel brake. The adjusting screw

[B]

can be used to change

the basic position of the hand brake lever (see maintenance work on chassis

and engine).

OPERATION INSTRUMENTS

Содержание EXC 200 EXC







































































Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды

KTM EXC 200 EXC, Руководство пользователя

Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды