KTM EXC 200 EXC страница 35 Скачать руководство пользователя

Страница: 35 / 70

ENGLISH

MAINTENANCE WORK ON CHASSIS AND ENGINE

Changing the basic position of the foot brake pedal *

The basic position of the foot brake pedal can be altered by turning the stop

screw

[5]

. The free play at the foot brake pedal must then be adjusted by

means of the piston rod

[6]

Measured on the outside, the foot brake pedal must have 3-5 mm (0.12–0.20

in) of free play before the piston rod can move the piston in the brake cylin-

der (to be recognised from the resistance on the foot brake pedal).

IF THIS FREE PLAY IS NOT PRESENT, THEN PRESSURE CAN BUILD UP IN THE

BRAKE SYSTEM WHEN DRIVING, CAUSING THE REAR WHEEL TO BRAKE.THE

BRAKING SYSTEM OVERHEATS AND MAY EVEN FAIL COMPLETELY IN EXTREME

CASES.

Checking the rear brake fluid level

The reservoir for the rear brake disk is located on the right side of the motor-

cycle on the rear brake cylinder.

No air bubble should be visible in inspection glass

[A]

when the vehicle is

parked in a vertical position.

IF THE BRAKE FLUID LEVEL DROPS BELOW THE MINIMUM EITHER THE BRAKE

SYSTEM HAS A LEAK OR THE BRAKE PADS ARE COMPLETELY WORN. IN THIS CASE,

CONSULT AN AUTHORIZED KTM DEALER IMMEDIATELY.

Refilling the rear brake fluid reservoir *

Add brake fluid as soon as a bubble is visible in inspection glass

[A]

To top up, remove screw

[7]

. Fill DOT5.1 brake fluid (e.g. Motorex Brake Fluid

5.1) up to the mark

[B]

on the inside of the reservoir and remount the screw.

Spilled brake fluid must be rinsed off with water.

– NEVER USE DOT5 BRAKE FLUID! IT IS BASED ON SILICONE OIL AND OF A

PURPLE COLOR. SEALS AND BRAKE HOSES MUST BE ESPECIALLY ADAPTED

TO IT.

– STORE BRAKE FLUID OUT OF REACH OF CHILDREN.

– BRAKE FLUID CAN CAUSE SKIN IRRITATION. AVOID CONTACT WITH SKIN AND

EYES. IF YOU GET BRAKE FLUID IN YOUR EYES, RINSE WITH PLENTY OF WATER

AND CONSULT A DOCTOR.

– DON’T LET BRAKE FLUID GET IN CONTACT WITH PAINT, IT IS AN EFFECTIVE

PAINT REMOVER.

– USE ONLY CLEAN BRAKE FLUID TAKEN FROM A TIGHTLY SEALED CONTAINER.

Replacing the front brake pads *

Press the brake caliper toward the brake disk, to put the brake piston in its

basic position. Remove clips

[1]

and pull out bolt

[2]

. Remove brake pads

from the brake caliper. Clean the brake caliper and the brake caliper support

with compressed air. Check the sleeves of the guide bolts for damage, and

grease guide bolts if necessary.

Mount the right brake pad and fix it with the bolt. Mount the left brake pad

and insert the bolt until it stops. Mount the clips.

When mounting the brake pads, be sure to check for correct fit of the

sliding metal-sheet

[3]

in the caliper support and of the leaf spring

[4]

– IT IS VERY IMPORTANT TO KEEP THE BRAKE DISK FREE FROM OIL AND FATTY

MATTERS. OTHERWISE, THE BRAKING EFFECT WOULD BE STRONGLY REDUCED.

– AFTER ASSEMBLY, CHECK IF CIRCLIPS HAVE BEEN FITTED CORRECTLY.

– AFTER WORKING ON THE BRAKING SYSTEM, ALWAYS ACTUATE THE HAND BRAKE

LEVER OR FOOT BRAKE LEVER, RESPECTIVELY TO ENSURE THAT THE BRAKE

PADS WILL LIE AGAINST THE BRAKE DISK AND THE PRESSURE POINT IS ESTAB-

LISHED.

3-5mm

Содержание EXC 200 EXC







































































Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды

KTM EXC 200 EXC, Руководство пользователя

Результаты поиска

Содержание EXC 200 EXC

Отзывы:

Похожие инструкции для EXC 200 EXC

Бренды по названию

Популярные бренды