manualshive.com logo in svg

KTM DUKE 640 e, Руководство пользователя

Поделиться
Скачать
KTM DUKE 640 e Скачать руководство пользователя страница 34

ENGLISH

32

To allow the air to escape from the front pipe of the frame, remove plug 

8

next to the steering head. Start engine and let it run in idle (1-2 minutes)
until oil escapes at the bore 

B

. As soon as oil starts to escape, turn off the

engine, and mount plug together with the gasket.

!

CAUTION

!

D

O NOT REV UP THE ENGINE DURING THE BLEEDING PROCEDURE BECAUSE NOT ALL THE

LUBRICATING POINTS WILL ALREADY HAVE BEEN SUPPLIED WITH SUFFICIENT AMOUNTS OF OIL

.

Warm up engine, check engine oil level and refill up to the marking MAX.
Finally, check the oil system for leaks.

!

CAUTION

!

I

NSUFFICIENT OIL OR POOR QUALITY OIL RESULTS IN PREMATURE WEAR OF THE ENGINE

.

U

SE ONLY RECOMMENDED BRAND MULTIGRADE ENGINE OILS FOR

4-

STROKE ENGINES

FOR LUBRICATING THE ENGINE

.

N

OTE

: 

D

ISPOSE OF USED OIL PROPERLY

! U

NDER NO CIRCUMSTANCES MAY USED OIL BE DISPO

-

SED OF IN THE SEWAGE SYSTEM OR IN THE OPEN COUNTRYSIDE

. 1 

LITER OIL CONTAMI

-

NATES

1.000.000 

LITER WATER

.

Changing oil filter *

Replace the oil filter when changing the engine oil. Press the foot brake
pedal and place a screwdriver or similar between foot brake pedal and
stopper roll so that the oil filter cover is more accessible. Remove banjo bolt

1

and the three screws. Remove oil filter cover 

2 

and oil filter. Clean fil-

ter housing, oil filter cover, and sealing surfaces. Check oil duct in oil filter
cover if clogged.

Check the O-ring 

3

for damage. O-rings need not be replaced unless

damaged. Press the O-ring into the groove of the filter cover. Fit new oil
filter 

4

with rubber gasket on the fitting in oil filter cover and mount cover

with filter. Mount three screws and tighten with 5 Nm (4 ft.lb). Mount hol-
low screw with seal rings and tighten with 15 Nm (11 ft.lb). Start engine
and check oil system for leakage.

Changing the fine screen filter *

Replace the fine screen filter when changing the engine oil. To do so, loo-
sen the three screws and remove the cover 

5

. Loosen the fine screen filter

with an oil filter wrench; you will be able to unscrew it the rest of the way
with your bare hand. Let engine oil flow out of the main frame tube. 
Clean sealing surfaces on the frame tube 

6

, fill new fine screen filter with

engine oil, and oil rubber seal 

7

. Replace fine screen filter and screw it

back in place, your bare hand will do. 
Start motor, bleed oil system (see Changing the Engine Oil) and make sure
fine screen filter does not leak.

!

CAUTION

!

– U

SE ONLY ORIGINAL

KTM 

FINE SCREEN FILTERS

. U

SING ANOTHER FILTER BRAND

CAN RESULT IN DAMAGE TO THE ENGINE

.

– I

F THE ENGINE OIL HAS BEEN DRAINED FROM THE FRONT PIPE OF THE FRAME

, 

YOU

MUST BLEED THE OIL SYSTEM

!

8

B

2

3

4

1

5

6

7

1

2

Содержание DUKE 640 e













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды