KTM 620 2001, Руководство пользователя

Страница: 30 / 41

ENGLISH
29
1
2
A
B
1
8
Cleaning of air filter*
To do this, remove the seat and the air filter cover from the air filter box.
Unclap the filter holder
1
, swing back and remove air filter plus filter carrier
from the filter box.
!
CAUTION
!
D
O NOT CLEAN AIR FILTER WITH FUEL OR PETROLEUM SINCE THESE DAMAGE THE FOAM
.
KTM
RECOMMENDS THE PRODUCTS OF THE COMPANY
PUTOLINE
FOR AIR FILTER
MAINTENANCE
.
Thoroughly wash the air filter in special cleaning fluid and allow to dry well.
Only press out the filter, do not wring out under any circumstances. Oil the
dry air filter with a high grade filter oil. Also clean the air filter box. Check
carburetor collar for damage and that it is fitted correctly.
Mount the air filter on the filter support
2
. Grease the front side
A
of the
filter, to improve the seal. Mount the air filter and the filter support in the
filter box. Make sure they are centered
B
, and lock into place with the filter
holder
1
.
! CAUTION !
– H
AVING MOUNTED THE AIR FILTER
,
CHECK IT FOR CORRECT FIT
. T
HE FRONT END
A
MUST ABOUT THE AIR FILTER BOX
. O
THERWISE
,
DUST AND DIRT MAY GET INTO THE
ENGINE AND LEAD TO INCREASED WEAR
.
– N
EVER OPERATE YOUR MOTORCYCLE WITHOUT AIR FILTER
. O
THERWISE
,
DUST AND
DIRT MAY GET INTO THE ENGINE AND LEAD TO INCREASED WEAR
.
Exhaust system *
Aluminium silencers are filled with glass fiber yarn. If exposed to heat for
longer periods of time, however, the glass fiber yarn pack will come unra-
velled, which can reduce both overall performance and the performance of
the silencer. Experience has shown that the front glass fiber pack
3
must
be replaced more often than the rear pack
4
.
To replace the front glass fiber yarn pack, remove the silencer. Remove the
front cap
5
, pull the front glass fiber yarn pack out of the silencer, mount a
new pack on the internal exhaust pipe, insert the internal exhaust pipe into
the silencer and replace the cap.
To replace the rear glass fiber yarn pack, drill the rivets open and remove
the rear cap
6
.
NOTE:
Always renew the O-rings
7
.
Glass fiber yarn packs are available in your KTM store.
WARNING
T
HE EXHAUST SYSTEM BECOMES VERY HOT WHILE THE MOTORCYCLE IS RUNNING
.
TO
AVOID BURNS
D
O NOT START WORK ON THE EXHAUST SYSTEM UNTIL IT HAS PROPERLY
COOLED DOWN
.
Draining of float chamber of the carburetor
Following every wet-cleaning procedure, the float chamber of the carbure-
tor should be drained in order to remove any water that may have penetra-
ted into it. Water in the float chamber leads to engine malfunction.
Make sure you do this while the engine is cold. Close the fuel tap, and place
a cloth under the carburetor, which is capable of absorbing the leaking fuel.
Unscrew the plug
8
, and clean it with compressed air. Then, mount plug
together with gasket, open fuel tap, and check float chamber for leaks.
WARNING
F
UEL IS EASILY FLAMMABLE AND TOXIC
. W
HEN HANDLING FUEL
,
BE SURE TO EXERCISE
THE UTMOST CAUTION
. N
EVER PERFORM ANY WORK ON THE FUEL SYSTEM IN THE PRO
-
XIMITY OF OPEN FLAMES OR BURNING CIGARETTES
. A
LWAYS ALLOW THE ENGINE TO
COOL OFF FIRST
. I
MMEDIATELY CLEAN UP ANY FUEL WHICH MAY HAVE BEEN SPILLED
.
M
ATERIALS SATURATED WITH FUEL ARE ALSO EASILY FLAMMABLE
. I
N CASE YOU INGESTED
FUEL OR FUEL SPLASHED INTO YOUR EYES
,
CONSULT A DOCTOR IMMEDIATELY
.
8
7
6
5
3 4