KTM 250 EXC-F 2018 Скачать руководство пользователя

Страница: 21 / 48

3 WORK

3.1

Raising the motorcycle with the lift stand

401942-01

Note

Danger of damage

The parked vehicle can roll away or fall

over.

–

Park the vehicle on a firm and level surface.

–

Raise the motorcycle at the frame underneath the engine.

Lift stand (78129955100)

Neither wheel is in contact with the ground.

–

Secure the motorcycle against falling over.

3.2

Removing the motorcycle from the lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

401943-10

–

Remove the motorcycle from the lift stand.

–

Remove the lift stand.

–

To park the motorcycle, press side stand

to the ground

with your foot and lean the motorcycle on it.

Info

While riding, the side stand must be folded up and
secured with the rubber band.

3.3

Removing the headlight mask with the headlight

V00458-10

(EXC

‑

F EU/AU/BR, EXC

‑

F Six Days)

–

Detach the brake line and wiring harness from the head-
light mask.

–

Release rubber bands

. Slide the headlight mask up

and swing it forward.

Содержание 250 EXC-F 2018

















































Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды

KTM 250 EXC-F 2018, Инструкции по установке

Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды