KTM 250 EXC-F 2018 Скачать руководство пользователя страница 40

Страница: 40 / 48

3 WORK

3.22

Closing filler cap

M01472-11

–

Replace the filler cap and turn clockwise until the release but-
ton

locks in place.

Info

Route the fuel tank breather hose

without kinking.

3.23

Refueling

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

Note

Material damage

Inadequate fuel quality causes the fuel filter to quickly become clogged.

In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in
problems with the fuel system.

–

Refuel only with clean fuel that meets the specified standards.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

–

Switch off the engine.

–

Open the filler cap. (

p. 37)

Содержание 250 EXC-F 2018

















































Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды

KTM 250 EXC-F 2018, Инструкции по установке

Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды