KTM 250 EXC-F 2018 Скачать руководство пользователя страница 7

Страница: 7 / 48

2 SETUP

S01414-10

(EXC

‑

F EU/AU/BR/US)

–

Take off screws

and handlebar supports.

–

Move the handlebar supports to the desired position and
mount and tighten screws

Guideline

Screw, handle-
bar holder

M10

40 Nm (29.5 lbf ft)

Loctite

243™

Info

Position the left and right handlebar supports
evenly.

E00483-01

Warning

Danger of accidents

A repaired handlebar poses a

safety risk.
If the handlebar is bent or straightened, the mate-
rial becomes fatigued. The handlebar may break
as a result.

–

Change the handlebar if the handlebar is dam-
aged or bent.

–

Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-
rectly.

–

Position the handlebar clamps. Mount and tighten the
screws evenly.
Guideline

Screw, handlebar
clamp

20 Nm
(14.8 lbf ft)

Info

The markings on the handlebar should be at the
center of the handlebar clamps.
Keep the gap widths equal when tightening.

Содержание 250 EXC-F 2018

















































Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды

KTM 250 EXC-F 2018, Инструкции по установке

Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды