KTM 250 EXC-F 2018 Скачать руководство пользователя

Страница: 5 / 48

2 SETUP

2.1

Unpacking and setting up the vehicle

E00851-10

Condition

Packaging

–

Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling
over.
To avoid damaging the motorcycle during the setup,
leave the protective film on the vehicle until you
have finished.

–

Remove the separate enclosure and unpack it. Check that
the scope of supply is complete using the enclosed pack-
ing list.

–

Have a lift stand available.

Lift stand (78129955100)

–

Carefully loosen and remove the tension belt of the footrest
mount.

Info

An assistant prevents the motorcycle from falling
over.

402050-01

–

Together with an assistant, take the vehicle off the pallet.

–

Position the vehicle on a lift stand.

–

Check the vehicle for transport damage.

–

Remove the headlight mask with the headlight. (

p. 19)

H01768-10

–

Position the turn signal indicator lamp

in the

speedometer bracket.

Содержание 250 EXC-F 2018

















































Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды

KTM 250 EXC-F 2018, Инструкции по установке

Результаты поиска

Содержание 250 EXC-F 2018

Отзывы:

Похожие инструкции для 250 EXC-F 2018

Бренды по названию

Популярные бренды