KTM 125 Duke DE Скачать руководство пользователя | Manualshive

Страница: 48 / 267

background image

11

FUEL TANK, SEAT, TRIM

46

11.10

Installing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

–

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

–

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.
Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to get into the ground water, the ground, or the sewage system.

304886-11

Main work

–

Connect the fuel line.

–

Position hose clamp

1

.

304885-11

–

Remove tool

2

.

304881-11

–

Plug in connector

3

.

304880-11

–

Position the fuel tank.

–

Position the holder

4

.

«
...
46
47
48
49
50
...
»

Содержание 125 Duke DE












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 125 Duke DE

V-Gard 500 Series

Бренд: MSA Страницы: 2

SBL.04.650.10000/B

Бренд: SW-Motech Страницы: 2

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

Бренд: Miller Страницы: 12

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

Бренд: Honda Страницы: 224

Бренд: Sinnis motorcycles Страницы: 68

Бренд: B&G electronics Страницы: 3

TRACER MTT9K 2019

Бренд: Yamaha Страницы: 122

TT-R125(N) 2000

Бренд: Yamaha Страницы: 508

TT-R125(R) 2002

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 610

TT-R125(S) 2003

Бренд: Yamaha Страницы: 610

Бренд: Yamaha Страницы: 616

Бренд: Yamaha Страницы: 90

Бренд: dushi Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды