KTM 125 Duke DE Скачать руководство пользователя

Страница: 216 / 267

SERVICE SCHEDULE

214

24.1

Service schedule

Every 10,000 km (6,214 mi) or every 2 years

Every 5,000 km (3,107 mi) or annually

Once after 1,000 km (621.4 mi)

Check the functioning of the electrical equipment.

○

●

Read out the fault memory using the KTM diagnostics tool.

○

●

Change the engine oil and oil filter, clean the oil screen. (

p. 200)

○

●

Check the front brake linings. (

p. 66)

○

●

Check the rear brake linings. (

p. 70)

○

●

Check the brake discs. (

p. 54)

○

●

Check the brake lines for damage and leakage.

○

●

Check the rear brake fluid level. (

p. 73)

○

●

Check the shock absorber and fork for leaks.

○

●

Check the swingarm bearing.

●

Check the wheel bearing for play.

●

Check the tire condition. (

p. 53)

○

●

Check the tire air pressure. (

p. 53)

○

●

Check the chain, rear sprocket, and engine sprocket. (

p. 59)

●

Check the chain tension. (

p. 58)

○

●

Grease all moving parts (e.g. side stand, hand lever, chain, ...) and check for smooth operation.

○

●

Clean the dust boots of the fork legs. (

p. 15)

●

Check the brake fluid level of the front brake. (

p. 68)

○

●

Check the steering head bearing play. (

p. 26)

○

●

Change the spark plugs.

●

Check the valve clearance.

○

●

Check all hoses (e.g. fuel, cooling, bleeder, drainage, etc.) and bellows for cracking, leaks, and correct routing.

○

●

Check the antifreeze and coolant level. (

p. 195)

○

●

Check the cables for damage and routing without sharp bends.

●

Check that the throttle cables are undamaged, routed without sharp bends, and set correctly.

○

●

Change the air filter. Clean the air filter box.

●

Check the screws and nuts for tightness.

○

●

Change the front brake fluid. (

p. 69)

●

Change the rear brake fluid. (

p. 74)

●

Check the headlight setting. (

p. 77)

○

●

Check that the radiator fan is functioning properly.

○

●

Final check: Check the vehicle for roadworthiness and take a test ride.

○

●

Read out the fault memory using the KTM diagnostics tool after a test ride.

○

●

Make the service entry in

KTM DEALER.NET

and in the service record.

○

●

○

One-time interval

●

Periodic interval

Содержание 125 Duke DE












































































































































































































































































Результаты поиска

Содержание 125 Duke DE

Отзывы:

Похожие инструкции для 125 Duke DE

Бренды по названию

Популярные бренды

KTM 125 Duke DE, Руководство по ремонту

Результаты поиска

Содержание 125 Duke DE

Отзывы:

Похожие инструкции для 125 Duke DE

Бренды по названию

Популярные бренды