KTM 125 Duke DE Скачать руководство пользователя | Manualshive

Страница: 68 / 267

background image

14

BRAKE SYSTEM

66

14.1

Checking the front brake linings

Warning

Danger of accidents

Reduced braking efficiency caused by worn brake linings.

–

Change worn brake linings immediately.

Note

Danger of accidents

Reduced braking efficiency caused by damaged brake discs.

–

If the brake linings are not changed in time, the steel brake lining carriers grind on the brake disc. The braking effect is greatly
reduced and the brake discs are destroyed. Check the brake linings regularly.

B00739-10

–

Check the brake linings for minimum thickness

A

.

Minimum thickness

A

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the front brake linings. (

–

Check the brake linings for damage and cracking.
» If there is wear or tearing:

–

Change the front brake linings. (

14.2

Changing the front brake linings

Warning

Skin irritation

Brake fluid can cause skin irritation on contact.

–

Avoid contact with skin and eyes, and keep out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Danger of accidents

Reduced braking efficiency due to old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule.

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Danger of accidents

Reduced braking efficiency due to use of non-approved brake linings.

–

Brake linings available from accessory suppliers are often not tested and approved for use on KTM vehicles. The construc-
tion and friction factor of the brake linings and therefore the brake power can differ considerably from the original KTM
brake linings. If brake linings are used that differ from the originals, there is no guarantee that they comply with the origi-
nal license. The vehicle no longer corresponds to the condition at delivery, and the warranty is no longer valid.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

«
...
66
67
68
69
70
...
»

Содержание 125 Duke DE












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 125 Duke DE

Бренд: PACIFIC CYCLE Страницы: 112

X-903 Ultra Carbon 29

Бренд: X-lite Страницы: 116

Бренд: KTM Страницы: 163

Бренд: Honda Страницы: 28

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 26

Бренд: MOTO GUZZI Страницы: 209

Бренд: YCF Страницы: 78

Бренд: oset Страницы: 44

Бренд: Denali Страницы: 5

Бренд: GYS Страницы: 36

Бренд: AFX Страницы: 112

Virago XV1100K(C)

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 101

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: Wunderlich Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды