KTM 125 Duke DE Скачать руководство пользователя | Manualshive

Страница: 196 / 267

background image

18

WATER PUMP, COOLING SYSTEM

194

18.1

Draining the coolant

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

Condition

The engine is cold.

Preparatory work

–

Remove the front spoiler. (

B00768-10

Main work

–

Stand the motorcycle upright.

–

Place a suitable container under the engine.

–

Remove screw

1

.

–

Remove the radiator cap.

–

Completely drain the coolant.

–

Mount screw

1

with a new seal ring and tighten it.

Guideline

Plug, water pump drain hole (125
Duke)

M6

8 Nm (5.9 lbf ft)

Plug, water pump drain hole (200
Duke)

M6

8 Nm (5.9 lbf ft)

18.2

Filling/bleeding the cooling system

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If coolant is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

B00767-11

–

Remove radiator cap

1

.

B00769-10

–

Remove bleeder screw

2

.

–

Tilt the vehicle slightly to the right.

–

Pour in coolant until it emerges without bubbles at the vent hole, and then mount
and tighten the bleeder screw immediately.

Alternative 1

Coolant (

Alternative 2

Coolant (mixed ready to use) (

«
...
194
195
196
197
198
...
»

Содержание 125 Duke DE












































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 125 Duke DE

Бренд: KAYO MOTOR Страницы: 84

Бренд: DUCATI Performance Страницы: 9

DaVinci RSV4-APRC

Бренд: STARLANE Страницы: 2

Бренд: XPOtool Страницы: 4

MASTERFOX 125cc 2015

Бренд: d'Magna Страницы: 29

Бренд: Honda Страницы: 161

Бренд: Suzuki Страницы: 80

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 18

Бренд: R&G Страницы: 17

Бренд: Thunderbike Страницы: 8

Бренд: Britannia Страницы: 9

Бренд: IBEX Страницы: 3

USGENERAL 97071

Бренд: U.S. General Страницы: 8

Бренд: APRILIA Страницы: 268

2003 Chief Vintage

Бренд: Indian Motorcycle Страницы: 305

Бренд: Rally-Raid Страницы: 14

Бренд: Salewa Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды