KTM 125 Duke DE Скачать руководство пользователя

Страница: 202 / 267

LUBRICATION SYSTEM

200

–

Oil the O-ring of the oil filter cover. Mount the oil filter cover.

–

Mount and tighten the screws.
Guideline

Screw, oil filter cover (125 Duke)

8 Nm (5.9 lbf ft)

Screw, oil filter cover (200 Duke)

8 Nm (5.9 lbf ft)

Finishing work

–

Check the engine oil level. (

p. 198)

19.4

Changing the engine oil and oil filter, cleaning the oil screen

Warning

Danger of scalding

Engine oil and gear oil get very hot when the motorcycle is ridden.

–

Wear appropriate protective clothing and safety gloves. In case of burns, rinse immediately with lukewarm water.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Drain the engine oil only when the engine is warm.

Preparatory work

–

Remove the front spoiler. (

p. 47)

–

Stand the motorcycle on its side stand on a horizontal surface.

B00774-10

Main work

–

Place a suitable container under the engine.

–

Remove the oil drain plug

with the O-ring.

–

Remove oil screen

with the O-ring.

–

Completely drain the engine oil.

–

Clean the oil drain plug and oil screen thoroughly.

–

Position oil screen

and mount and tighten oil drain plug

with the O-ring.

Guideline

Oil drain plug (125 Duke)

M24x1.5

15 Nm
(11.1 lbf ft)

Oil drain plug (200 Duke)

M24x1.5

15 Nm
(11.1 lbf ft)

B00775-10

–

Remove screws

. Remove the oil filter cover

with the O-ring.

–

Pull oil filter

out of the oil filter housing.

Circlip pliers reverse (51012011000) (

p. 252)

–

Completely drain the engine oil.

–

Thoroughly clean the parts and sealing area.

B00776-10

–

Insert oil filter

–

Oil the O-ring of the oil filter cover. Mount oil filter cover

–

Mount and tighten the screws.
Guideline

Screw, oil filter cover (125 Duke)

8 Nm (5.9 lbf ft)

Screw, oil filter cover (200 Duke)

8 Nm (5.9 lbf ft)

Info

Too little engine oil or poor-quality engine oil results in premature wear to
the engine.

Содержание 125 Duke DE












































































































































































































































































Результаты поиска

Содержание 125 Duke DE

Отзывы:

Похожие инструкции для 125 Duke DE

Бренды по названию

Популярные бренды

KTM 125 Duke DE, Руководство по ремонту

Результаты поиска

Содержание 125 Duke DE

Отзывы:

Похожие инструкции для 125 Duke DE

Бренды по названию

Популярные бренды