KTM 1190 RC8 R Track Скачать руководство пользователя страница 21

Страница: 21 / 127

CONTROLS

Press the button
and the button
for 3 - 5 seconds.

The display changes to the

SET

‑

Press the

MODE

button for 3 -

5 seconds.

All values in

RACE

mode are reset (except

RACEODO

)

Press the

MODE

button

briefly.

Next display mode

5.21

Maximum lap speed menu, TOPSPEED

400445-01

Condition
Alternative 1

• The ignition is on.
• The motorcycle is stationary.
•

RACE

mode

Alternative 2

• The ignition is on.
• The motorcycle is being ridden.
•

RACE

mode

–

Press the

MODE

button briefly and repeatedly until

TOPSPEED

appears at the top left

of the info display.

TOPSPEED

shows the highest lap speed.

If an

appears after

TOPSPEED

, the stopwatch is running in the background.

If a

appears after

TOPSPEED

, the stopwatch in the background is active but waiting

for a speed signal. The time is not running.
This function is controlled with the

LAP

button.

LastLap

shows the maximum speed of the last lap.

±Last

shows the maximum speed difference between the last lap and the lap before.

±Best

shows the maximum speed difference between the last lap and the highest maxi-

mum speed.
If the last lap was the lap with the highest maximum speed, the info display shows

±Best

Best!

Press the button . No function
Press the button . No function
Press the button
and the button
for 3 - 5 seconds.

The display changes to the

SET

‑

Press the

MODE

button for 3 -

5 seconds.

The display of

LastLap

±Last

and

±Best

are set to

Press the

MODE

button

briefly.

Next display mode

5.22

LAP/BESTLAP/LastLap menu

400446-01

Condition

• The ignition is on.
• The motorcycle is stationary.
•

RACE

mode

–

Press tje

MODE

button briefly and repeatedly until

LAP/BESTLAP/LastLap

appears in

the info display.

LAP

shows the selected lap.

BESTLAP

shows the number of the lap with the best lap time.

LastLap

shows the time of the lap behind

LAP

±Lap

shows the difference to the lap before.

±Lap

shows the difference to the lap after.

Press the button . The next lap is displayed
Press the button . The previous lap is displayed

Содержание 1190 RC8 R Track
































































































































Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Бренды по названию

Популярные бренды

KTM 1190 RC8 R Track, Руководство пользователя

Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Бренды по названию

Популярные бренды