KTM 1190 RC8 R Track Скачать руководство пользователя

Страница: 18 / 127

CONTROLS

Press the

MODE

button for 3 -

5 seconds.

The display of

Trip 1

Time 1

and

Avs 1

is reset

Press the

MODE

button

briefly.

Next display mode

5.16

Odometer menu, ODO/Trip 2

400579-01

Condition
Alternative 1

• The ignition is on.
• The motorcycle is stationary.
•

ROAD

mode

Alternative 2

• The ignition is on.
• The motorcycle is being ridden.
•

ROAD

mode

–

Press the

MODE

button briefly and repeatedly until

ODO

appears at the top left of

the info display.

ODO

shows the total distance covered.

Trip 2

shows the distance covered since the last reset. For example, between two refu-

eling stops.

Trip 2

is always running and counts up to

9999.9

Time 2

shows the journey time on the basis of

Trip 2

and resumes running as soon as a

speed signal is received.
The calculation of this value starts with the first speed signal and ends 3 seconds after
the last speed signal.

Avs 2

shows the average speed and is coupled with

Trip 2

and

Time 2

Press the button . No function
Press the button . No function
Press the button
and the button
for 3 - 5 seconds.

The display changes to the

SET

‑

Press the

MODE

button for 3 -

5 seconds.

The display of

Trip 2

Time 2

and

Avs 2

is reset

Press the

MODE

button

briefly.

Next display mode

5.17

FUELDISTANCE menu

401202-01

Condition
Alternative 1

• The ignition is on.
• The motorcycle is stationary.
•

ROAD

mode

Alternative 2

• The ignition is on.
• The motorcycle is being ridden.
•

ROAD

mode

–

Press the

MODE

button briefly and repeatedly until

FUELDISTANCE

appears at the top

of the info display.

TripFuel

- No function

OuterTemp

- No function

Tip

The

OuterTemp

display can be switched off in the

OPTIONS

menu.

OuterTemp

then no longer appears on the info display.

Press the button . No function
Press the button . No function

Содержание 1190 RC8 R Track
































































































































Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Похожие инструкции для 1190 RC8 R Track

Бренды по названию

Популярные бренды

KTM 1190 RC8 R Track, Руководство пользователя

Результаты поиска

Содержание 1190 RC8 R Track

Отзывы:

Похожие инструкции для 1190 RC8 R Track

Бренды по названию

Популярные бренды