21
Operating Manual ECOTROC ATCN 15-110
9.4 Overview of maintenance parts
The following maintenance parts should be replaced every year:
ATCN 15
ATCN 18
ATCN 22
ATCN 34
ATCN 45
ATCN 55
ATCN 75
ATCN 90
ATCN 110
GTE7311DMF
A4000-121
F-ATCN 15
GTE7311 DMF
A4000-121
F-ATCN 18
GTE7311 DMF
A4000-121
F-ATCN 22
GTE7411 DMF
A4000-121
F-ATCN 34
GTE7411 DMF
A4000-121
F-ATCN 45
GTE7411 DMF
A4000-121
F-ATCN 55
GTE8601 DMF
A4000-121
F-ATCN 75
GTE8601 DMF
A4000-121
F-ATCN 90
GTE8601 DMF
A4000-121
F-ATCN 110
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
After-filter element
Oil check pipe
Filling active carbon
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Every year
Every year / when required
rec. after 4.000 Bh / or 1 year
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Type
Component
Designation
Amount
Interval
Measure
9.5 Replacing the filter element
The job of the after-filter is to stop any abrasion dust that has built up from the active carbon. Proceed as follows
to replace this filter element:
1. Close the cut-off valves upstream and downstream of the adsorber.
2. Open the manual drain cock on the filter and wait until the pressure gauge on the adsorber shows „0“ bar.
3. Turn the bottom part of the filter in a clockwise direction to open it. Unscrew it completely and carefully put
it down.
4. Now you can remove the filter element out of the filter.
5. Use a damp cloth to clean inside the filter housing.
6. Check whether the O-ring in the filter head is OK. Replace if necessary.
7. Please fit the new filter element into the three pockets, on the inside of the filter bowl.
8. Screw the bottom part of the filter back in again and close the manual drain cock.
9. Slowly open the shut-off device at the outlet and check for leaks.
10. Once the pressure is back to normal again, slowly open the shut-off device at the outlet.
